Materials for the building industry

A shape-conscious alloy

Dec 16, 2014 | MARTINA PETER
When the frame of a pair of glasses is bent out of shape, it's not that easy to return it to its original form. If, however, your spectacles are made of a shape memory alloy then you don't have a problem. Just place the frame in hot water and bingo! – they're as good as new again. Empa researchers have now shown that these materials can also find applications in the building industry.

Forging an iron-based shape memory alloy (SMA) cast block: To shape the block, it is heated to around 1,150 degrees Celsius (photo: TU Bergakademie Freiberg, Institut für Metallformung).




Empa Innovation Award presented at ETIF 2014
This year’s Innovation Award was presented at the Empa Technology & Innovation Forum (ETIF). The prize went to a joint team from two labs, Structural Engineering and Joining Technologies & Corrosion, for the project Shape memory steel as a new pre-stressing material for the building industry – a successful collaboration between materials science and engineering, as Empa’s Deputy Director Peter Richner pointed out. The project uses shape memory alloys (SMAs) to prestress large concrete support structures, an approach which had previously been far too expensive. The newly developed, iron-based SMA turned this on its head meeting all requirements for use in concrete structures such as phase transformation temperature and corrosion behavior.


Shape memory alloys, or SMAs, possess the ability to return to their original shape after being severely deformed, either spontaneously or following the application of heat. This makes them useful materials, not just for making spectacle frames but also for technical applications such as thermostats, stents and micro-actuators. Other applications in the construction industry are conceivable too, for example in the reinforcement of bridges.
If a concrete beam is cast with reinforcing rods made of an SMA material, these can then be “activated” through the application of heat. They attempt to return to their original shape, but because of their concrete sheath they cannot do so, thus exerting a pre-stressing force on the beam. This effect can be used, for example, to pre-stress a complete bridge span. In order to generate the necessary force the SMA rods must simply be heated by passing an electric current through them. This obviates the need for using elaborate tensioning systems and jacket tubes, as used in conventional pre-stressing techniques.
The nickel titanium alloys used to make spectacle frames or stents are not very suitable for use in the construction industry. Iron-based SMA products are much more attractive, since both the raw materials and the processing costs are far cheaper. However, to date one problem has remained a stumbling block: to activate the memory effect the materials currently used must be heated up to 400° C, which for applications involving concrete or mortar, or other heat sensitive materials, is too high. Empa researchers led by Christian Leinenbach of the Joining Technology and Corrosion Laboratory have now succeeded in developing a novel iron-manganese-silicon SMA alloy which is activated at just 160° C, a temperature much more suitable for use with concrete. The material science researchers "designed" a range of virtual alloys using thermodynamic simulations, and then selected the most promising combinations. These were then manufactured in the laboratory and their shape memory characteristics tested, with great success. Several of the new materials met the construction engineers’ requirements, an important milestone on the path to providing economic shape memory steel alloys for industrial applications – in other words, manufacturing them by the ton.

Size 197 KB

A concrete beam, which was reinforced with two Fe-SMA laminates embedded in grooves: The laminates were heated – and thus prestressed – by passing an electric current through them (only the copper clamps and electricity cables are visible).


The long road from laboratory to finished product
Christoph Czaderski, of Empa's Engineering Structures Laboratory, believes that iron-based SMA materials have a promising future in the building industry since the process of pre-stressing is simpler and therefore cheaper than in conventional techniques. In addition they may allow engineers to create pre-stressed structures which are impossible or very difficult to achieve using conventional techniques. These include the use of short fibre concrete, near surface mounted laminates, column wrapping and ribbed armouring steel. A feasibility study financed by the Commission for Technology and Innovation (CTI) recently showed that it is possible to produce the new alloys on an industrial scale, not just a few kilos for laboratory use. The manufacturing process has been developed in collaboration with Leoben University (Austria), the Technical University Bergakademie Freiberg (Germany), and the German company G. Rau GmbH.
The working of cast ingots, each about 100 kg in weight, into thin strips around 2 mm thick or ribbed armouring steel rods at temperatures over 1000° calls for high degree of technical knowledge, and the appropriate infrastructure. The working process also needs to be adapted for use with the novel alloys.
  The metal strips produced in this way demonstrated their capabilities in the tests which followed, during which they were inserted into slits cut in the surface of concrete beams and fixed with adhesive.
To carry forward the developments made at Empa, a start-up company, re-Fer AG, has been set up. This will in future produce and distribute iron-based SMA for the construction industry. The cost of the new products is expected to be about the same order of magnitude as that for stainless steel based materials.
There are other pictures you can have a look at:
Picture sources (l.t.r.) No. 1, 2 and 3: Institut für Metallformung, TU Bergakademie Freiberg, No. 4: Firma G.RAU GmbH & Co. KG, Pforzheim, D

Further Information




Editor / Media Contact